![]() ![]() 1 went in fine right infront of the card, the other, again please be aware when buying this case and you want 3 intake fans, the hardrive cage is in the way of the third fan. However, in order to get 2 more fans for intake, I had to buy 15mm fans. ![]() ![]() Psu shroud install#I had to move the already installed fan all the way to the top, and was able to install the card no bigge. Please note, it does, however you will not be able to fit 2 fans on the front for intake. I got this case for my first build and made sure it would fit a 3070ti. Overall, I love this case, I can't stop admiring it, it was well worth re-building my PC. It has little rubber pads on the tray which the drive sits on and they work great. But in this case I can only hear my drives when I'm holding my ears up to the case which is a crazy difference to the tooth-grating sound I had to deal with before. One of the things I love about it the most are the hard drive trays - my last case had my 7200 drives rumbling like crazy, I even replaced one because I thought it was faulty. I also had to arrange my power supply cables carefully because the cables are round and very thick, but overall I found managing cables to be quite easy. The reduced space does make certain things more difficult, for example fitting the SATA cables into my ATX motherboard was difficult because there wasn't much room at the side for me to access the slots. One of the reasons I swapped is because I wanted a smaller, lighter case, and this one is a nice size and weight without being cramped or flimsy. Visually I think it's gorgeous, I have the white version and it looks very sleek and elegant with the mesh front panel. Psu shroud manual#Highly recommend it for newbie builders as it comes with a manual and all screws are labelled inside which you may not find in cheap cases. Psu shroud Pc#I did a case swap into this case (previous case was a GameMax Vanguard VR2 and my first PC build), and this case was such a pleasure to build in in comparison. Main advice chhose parts to go in this wisely. I should have got the Meshify 2 but everything is in place now and cooling is excellent aith all temps on cpu and gpu staying low. The case specs say it will take a long GPU but not if you are front mounting a AIO. A smaller GPU would eliminate this issue. This was mainly because my GPU is three fanhned at quite long. The the fands had to be put in a push through configuration and even then because of space they pushed the front silter out so it only clips in a top and bottom. a great AIO but woulds not fit in top mount position so have to put it in front. The AIO is question is the Arctic Freezer II. The problem came though when trying to top mount the AIO. Psu shroud plus#I put a Asus Tuf Gaming B550 Plus in it which fitted perfectly. It does take an ATX card but to be honest think mATX would be better. However the C stands for Compact so bare this in mind when using for ATX build. This is a great case and bought off back of reviews. Also the Lian Li glass panels have a nasty habit of coming unglued and falling off.Reviewed in the United Kingdom on 9 February 2021 And I am also aware of cases like the Lian Li O11 XL, but I don't want any glass in my case (pets, kids). I know that front-to-back airflow works fine, but in the detailed testing above, 1 bottom intake, 1 rear exhaust, and 2 top exhaust was superior, and I suspect also quieter (as the fans are physically further away if the tower is sitting on a desk).Īdditionally, I am aware of cases like the Corsair 540, but that particular one has a bunch of janky plastic so it's a hard pass. it may overlap horizontally somewhat with the top of the PSU. Another is that the fan might not be located optimally to have clear airflow over the anterior end of the PSU i.e. One drawback I could see to mounting on top of the PSU shroud is potentially losing a PCIE slot. Frustratingly, they did test cases in separate articles that support fan mounting atop the PSU shroud, but they did not place fans there. l=&start=2 This is the best I could find, but they only tested intake at the bottom of the case. Has anyone done comparative thermal testing of having an:Ī) 140mm intake fan on top of the PSU shroud located anterior and superior to the PSUī) 140mm fan in the same anterior position, but at the bottom of the case with PSU shroud removed? This picture is for reference only and doesn't quite illustrate case B) because in that case, there would be no PSU shroud. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |